Rubicon Models

Rubicon Models => Official Assembly Instructions => Topic started by: Rubicon Models on July 03, 2017, 04:29:40 pm

Title: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: Rubicon Models on July 03, 2017, 04:29:40 pm
Assembly Instruction for SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23

(http://i1373.photobucket.com/albums/ag377/RubiconModels/Assembly%20Instructions/280048%20SdKfz%20250-9%20amp%20251-23%20170512-p1_zpsavxibjz4.jpg)

(http://i1373.photobucket.com/albums/ag377/RubiconModels/Assembly%20Instructions/280048%20SdKfz%20250-9%20amp%20251-23%20170512-p2_zps5lyqimd6.jpg)

(http://i1373.photobucket.com/albums/ag377/RubiconModels/Assembly%20Instructions/280048%20SdKfz%20250-9%20amp%20251-23%20170512-p3_zpsaqxbupqn.jpg)

(http://i1373.photobucket.com/albums/ag377/RubiconModels/Assembly%20Instructions/280048%20SdKfz%20250-9%20amp%20251-23%20170512-p4_zpsxrtxgxma.jpg)

Last Update: 170703
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: oreoc23 on February 09, 2018, 11:12:54 am
I've been looking at the instructions of the SdKfz 250/9 kit... I currently have 2 of the SdKfz 250/1 Neu Kits, but have not purchased the SdKfz 250/1 Alte yet. The Instructions below show both kits for the SdKfz 250/9 using the Floorboard Part E22 in the building of both the SdKfz 250/9 Alte & SdKfz 250/9 Neu... Since the Expansion Kit SdKfz 250/9 has only one Part E22, can I assume I should use it in the SdKfz 250/9 Alte so as to attach the 20mm KwK 38 Autocannon to the Floor of the SdKfz 250/9 Alte and leave the SdKfz 250/9 Neu without the Floorboard?   :o
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: Pinky on February 09, 2018, 12:24:07 pm
The instructions say that part 22 is only for the alte version.  The neu version didn't have the pedestal - the 20mm was attached to the (redesigned) turret.   
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: ultravanillasmurf on February 09, 2018, 04:50:56 pm
The instructions say that part 22 is only for the alte version.  The neu version didn't have the pedestal - the 20mm was attached to the (redesigned) turret.   
Step 5 is for the neu, and seems to use the part E22 (without the step 2a holes).

I would just put a black painted rectangle of plastic card in the bottom of the hull. You probably cannot see past the turret gubbins. Unless you are Ripley and have opened the back door ^__^.
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: Pinky on February 09, 2018, 05:11:27 pm
You're right, UVS - I've got the kit, but haven't built it.  But surely the floor isn't needed?
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: ultravanillasmurf on February 09, 2018, 05:30:17 pm
I agree it is not needed.

It would be an issue if you built the neu before the alte.
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: ripley on February 09, 2018, 09:26:35 pm
Hmm , now that you mention it , I do have 2 Neu kits and I've got the turret kit in transit from NSW ,  ;D
Title: Re: 280048 SdKfz 250/251 Expansion - SdKfz 250/9 & 251/23 - 2cm Autocannon
Post by: oreoc23 on February 10, 2018, 01:34:31 am
I should have listed the "Step Numbers" in my post, will do next time (IF there is a next time...).  Thanks Guys for the Replies! I was pretty sure I should save E22 for the Alte! I will do so now and not worry about the Neu! I plan on using my kits as Gaming Pieces so the rear hatch will be closed. I bought 3 of the 20mm KwK 38 Autocannon kits, 2 sets for the SdKfz 250/9 Alte & 2 for the SdKfz 250/9 Neu Kits and one set to convert the Warlord Puma to a SdKfz 234/1 until Rubicon does a "better" SdKfz 234 Series!  :o  I'm still hoping Rubicon will use the SdKfz 250 & 251 weapons expansion kits for the SdKfz 234 Series & Aufklärungspanzer 38(t) / SdKfz140/1  ;)