Author Topic: UVS models  (Read 21157 times)

somtec

  • Cadet
  • *
  • Posts: 35
    • View Profile
Re: UVS models
« Reply #315 on: January 07, 2018, 09:54:12 PM »
nice work, iam trying something on the hvss wheel front, trying to make mould, hopefully should be ok

ripley

  • Sergeant
  • ***
  • Posts: 774
    • View Profile
Re: UVS models
« Reply #316 on: January 08, 2018, 12:12:05 AM »
Well done , The extra bits you added look great .  Good idea to hide the tow cable end in the hull, they can be a pain to attach to wire or thread sometimes , I did the same thing on the BA T-34 after replacing the molded on cable , great minds think alike  ::) . To stretch out my cable ends , I tended to bury one end under stowage , so I don't need to use 2 on one model , can't really tell from the pics you posted but I assume you did the same thing .  IRC that " not exhaust pipe"  is something to do with cooling the transmission which is under that part of the nose .  Hot air out or maybe cool air in , as its down the side of the tank where it shouldn't suck in dust and dirt

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #317 on: January 09, 2018, 03:14:29 AM »
Thanks.

I made the clamp or clip out of greenstuff. Theoretically it is looped over the rear left tow hook, that is covered by the bucket handle (which I made out of wire as I lost the plastic one).
« Last Edit: January 09, 2018, 03:29:12 AM by ultravanillasmurf »

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #318 on: January 09, 2018, 03:17:50 AM »
Not quite what our gracious hosts had in mind for them...

Three British flimsy cans used to put the track units in a consistent location on an HLBSCo 1/48 scale resin BMD2 (two on the side being glued, one on the other side).

ripley

  • Sergeant
  • ***
  • Posts: 774
    • View Profile
Re: UVS models
« Reply #319 on: January 09, 2018, 08:45:17 AM »
What ever works .I've use all sorts of weird stuff  to level kits out  ( Lego is great ) Some kind of modern eastern block APC ?

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #320 on: January 09, 2018, 06:14:01 PM »
Some kind of modern eastern block APC ?
The BMD2 is a Soviet air portable IFV.

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #321 on: January 14, 2018, 03:12:25 AM »
So the Panzer IB is now "finished" (there is some dark paint required in the wheels).



The crew have stocked up on fuel cans and ammunition. They have also lifted a fire bucket.

I have the T34/76 kit scattered over my work table, so that is probably next (once I decide what version to build).
« Last Edit: January 14, 2018, 03:14:47 AM by ultravanillasmurf »

Pinky

  • Captain
  • ****
  • Posts: 1,381
    • View Profile
Re: UVS models
« Reply #322 on: January 14, 2018, 10:01:05 AM »
Hey, that turned out very well.  All ready to roll through the Kentish countryside!  Thanks for sharing.

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #323 on: January 15, 2018, 04:49:22 PM »
Work in progress on the T34/76.


I was going to build it "out of the box", but I ended up putting some hand rails on (aided by the Bill Bedford hand rail jig).

Still have bits to add.

ripley

  • Sergeant
  • ***
  • Posts: 774
    • View Profile
Re: UVS models
« Reply #324 on: January 15, 2018, 11:53:55 PM »
That's looking good . Where did you pick up that jig ? ( Found some on a Model RR site , is it 4mm or 7mm ?) That looks like it would work for all sorts of scales .  Surprised Rubicon hasn't included a jig on the T-34 sprues like they did for the Crusader light guards , except for the fact the Crusader kit came out after the T-34s  ::)
« Last Edit: January 16, 2018, 12:06:46 AM by ripley »

ultravanillasmurf

  • Captain
  • ****
  • Posts: 1,183
    • View Profile
    • Blog:
Re: UVS models
« Reply #325 on: January 16, 2018, 02:42:02 AM »
It is the 4mm (20mm or 1/76 scale) one. I used 0.45mm brass rod for the hand rails (I cheated on the rear one and made it one piece).

I have the 7mm (40mm or 1/43 scale one) which I think I used on the T34/85. That used 0.7mm brass rod.

I got them at a local model railway show.

ripley

  • Sergeant
  • ***
  • Posts: 774
    • View Profile
Re: UVS models
« Reply #326 on: January 16, 2018, 07:05:18 AM »
Thanks , I'll have to get one of those